AW: [SPAM] Re: [Xen-users] network bridge problem - xen 3.1 on debian etch

["Hinrich Aue" <hinrich.aue@xxxxxxxxxxxxxxxx>]

I use debian edge
Xen 3.1

I have two Ethernet cards. But I'm only using eth0. It's a 1000Mb card. bnx2
is the name of the driver module for the card.

--------------------------------------
bnx2: eth0 NIC Link is Up, 1000 Mbps full duplex, receive & transmit flow
control ON
--------------------------------------

I also switched the Ethernet cable - the right card is attached.

My network configuration is attached below

Everything else is default debian etch installation + default xen 3.1.0
binary installation.

Interfaces ---------------------------

# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
allow-hotplug eth0
iface eth0 inet static
        address 10.1.1.251
        netmask 255.255.255.0
        network 10.1.1.0
        broadcast 10.1.1.255
        gateway 10.1.1.254
        # dns-* options are implemented by the resolvconf package, if
installed
        dns-nameservers 10.1.1.253
        dns-search lci-software.com

# The sexondary network interface
allow-hotplug eth1
iface eth1 inet static
        address 10.1.2.251
        netmask 255.255.255.0
        network 10.1.2.0
        broadcast 10.1.2.255


---------------------------





-----Ursprüngliche Nachricht-----
Von: Martin Goldstone [mailto:m.j.goldstone@xxxxxxxxxxxxxxx] 
Gesendet: Tuesday, July 24, 2007 5:34 PM
An: Hinrich Aue; xen-users@xxxxxxxxxxxxxxxxxxx
Betreff: [SPAM] Re: [Xen-users] network bridge problem - xen 3.1 on debian
etch

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

Can you provide us with any more details of your networking setup, Xen
version, distro etc?

Mart

Hinrich Aue wrote:
> Hello group,
> 
>  
> 
> I'm having a problem with networking when booting xen kernel.
> 
>  
> 
> The networking works when booting in normal kernel.
> 
>  
> 
> But when booting into xen kernel, it does not work anymore.
> 
>  
> 
>  
> 
> The funny thing is that the bridge only shows RX packets, but 0 TX
packets.
> 
>  
> 
> I've also tried the ethtool -K device tx off with every network device.
> 
>  
> 
> Any idea what could be wrong?
> 
>  
> 
> Thanks,
> 
>             Hinrich
> 
> 
> 
> 
> ------------------------------------------------------------------------
> 
> _______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (MingW32)
Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org

iD8DBQFGphvNRnwIDhcMR9MRAm/EAKC0flOxOxCRx9GmU8qd3/Rn2vY4TACfX//u
pHPSYZywy2LgphMHHOxa9wQ=
=eFtX
-----END PGP SIGNATURE-----


_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users