Re: [Xen-users] Re: new domain respawns with xen3.0 on ubuntu

["Marco Crociani - Tyrael" <marco.crociani@xxxxxxxxx>]

Anoter solution is create the tty devices:
# cd /lib/udev/devices
# ./MAKEDEV tty2 tty3 tty4 tty5 tty6
# shutdown -r now

What is the best solution?
If there is only one tty device is possibile to connect 2,3 or more
times at once with xm console?

2006/5/30, Tijl Van den Broeck <subspawn@xxxxxxxxx>:
> You need to fix your inittab before booting the xen domU.
>
> /mnt/domu/etc/inittab:
> 1:2345:respawn:/sbin/getty 38400 console
>
> and comment the other 1-6 out. Now you've got yourself a console and booting
> should work.
>
> greetings
>
>
>
>
>
>
> On 5/30/06, Hardeep Singh < hardeepguru@xxxxxxxxx> wrote:
> >
>
> ooppss..!! posted the wrong fstab!
>
> The one for this domain is:
>
> /dev/hda1               /               ext3    defaults        1       2
> /dev/hda2               none            swap    sw            0       0
> /dev/pts                devpts          gid=5,mode=620    0       0
> none                    /dev/shm        tmpfs   defaults     0       0
>
> The one the previous post is the dom0 one!
>
> Regards,
> Hardeep
>
>
> On 5/29/06, Hardeep Singh < hardeepguru@xxxxxxxxx> wrote:
> >
> > I successfully installed xen3.0 on my machines. However there are a few
> problems when I try to create a new domain!
> >
> > The procedure I've followed is pretty much the same as given on pages 4-5
> on;
> >
> > http://www.howtoforge.com/perfect_setup_xen3_debian_p4
> >
> > On doing a ' xm create -c /etc/xen/vm1-config.sxp vmid=1' the following is
> what parts of the trace look like:
> >
> > NET: Registered protocol family 20
> > Using IPI No-Shortcut mode
> > EXT2-fs warning (device hda1): ext2_fill_super: mounting ext3 filesystem
> as ext2
> > VFS: Mounted root (ext2 filesystem) readonly.
> > Freeing unused kernel memory: 168k freed
> > 8250: no version for "struct_module" found: kernel tainted.
> > 8250: Unknown symbol uart_get_baud_rate
> > 8250: Unknown symbol uart_resume_port
> > 8250: Unknown symbol uart_register_driver
> > 8250: Unknown symbol uart_suspend_port
> > 8250: Unknown symbol uart_remove_one_port
> > 8250: Unknown symbol uart_update_timeout
> > 8250: Unknown symbol uart_unregister_driver
> > 8250: Unknown symbol uart_get_divisor
> > 8250: Unknown symbol uart_match_port
> > 8250: Unknown symbol uart_add_one_port
> > 8250: Unknown symbol uart_write_wakeup
> > modprobe: FATAL: Error inserting 8250
> (/lib/modules/2.6.16-xen/kernel/drivers/serial/8250.ko):
> Unknown symbol in module, or unknown parameter (see dmesg)
> >
> > INIT: version 2.86 booting
> > * Files under mount point '/dev/shm' will be hidden.
> > Will now activate swap.
> > swapon on /dev/hda2
> > swapon: cannot stat /dev/hda2: No such file or directory
> > * Swap activation failed with error code 255.
> > Will now check root file system.
> > fsck 1.39-WIP (31-Dec-2005)
> > [/sbin/fsck.ext3 (1) -- /dev/shm/root] fsck.ext3 -a -C0 /dev/shm/root
> > /dev/shm/root: clean, 25155/640000 files, 193537/1280000 blocks
> >
> > Will now mount local filesystems.
> > mount: mount point devpts does not exist
> > none on /dev/shm type tmpfs (rw)
> > * Mounting local filesystems failed with error code 96.
> > Will now activate swapfile swap.
> > Done activating swapfile swap.
> >
> > * /etc/network/options is deprecated.
> > Setting up IP spoofing protection...done (rp_filter).
> > Configuring network interfaces...done.
> > Starting portmap daemon....
> >
> > Starting deferred execution scheduler: atd.
> > Starting periodic command scheduler....
> > INIT: Id "1" respawning too fast: disabled for 5 minutes
> > INIT: Id "2" respawning too fast: disabled for 5 minutes
> > INIT: Id "5" respawning too fast: disabled for 5 minutes
> > INIT: Id "3" respawning too fast: disabled for 5 minutes
> > INIT: Id "4" respawning too fast: disabled for 5 minutes
> > INIT: Id "6" respawning too fast: disabled for 5 minutes
> > INIT: no more processes left in this runlevel
> > INIT: Id "1" respawning too fast: disabled for 5 minutes
> > INIT: Id "2" respawning too fast: disabled for 5 minutes
> > INIT: Id "5" respawning too fast: disabled for 5 minutes
> > INIT: Id "3" respawning too fast: disabled for 5 minutes
> > INIT: Id "4" respawning too fast: disabled for 5 minutes
> > INIT: Id "6" respawning too fast: disabled for 5 minutes
> > INIT: no more processes left in this runlevel
> >
> >
> >
> > my /etc/fstab for this machine looks like:
> > proc            /proc           proc    defaults        0       0
> > /dev/hda1       /               ext3    defaults,errors=remount-ro 0
> 1
> > /dev/hda5       none            swap    sw              0       0
> >
> > and the domain configuration file is attahed.
> >
> > Any sort of help would be appreciated! I've been stuck here since pretty
> long :(
> >
> > Regards,
> > Hardeep
> >
> >
> >
> >
> > --
> >
> > hardeep
> >
>
>
>
> --
> hardeep
>
> _______________________________________________
> Xen-users mailing list
>  Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users
>
>
>
> _______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users
--
Marco Crociani - Tyrael
* Perchè usare Formati Aperti? - http://www.openformats.org
* Debian GNU/Linux - http://www.debian.org

_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users