[Xen-devel] boot errors

[Stephan Böni <boeni@xxxxxx>]

I've compiled the 3.0-devel version on SUSE Linux 9.3. The ony problem is the 
qla2300 driver, which will not start all correctly on boot. So i cannot see 
other partitions than sda.

---------------------------------------------------------------------------------
QLogic Fibre Channel HBA Driver
ACPI: PCI Interrupt 0000:04:02.0[A] -> GSI 24 (level, low) -> IRQ 185
qla2300 0000:04:02.0: Found an ISP2312, irq 185, iobase 0xf8840000
scsi3 : qla2xxx
qla2300 0000:04:02.0: Configuring PCI space...
qla2300 0000:04:02.0: Configure NVRAM parameters...
qla2300 0000:04:02.0: Verifying loaded RISC code...
qla2300 0000:04:02.0: Waiting for LIP to complete...
qla2300 0000:04:02.0: LIP reset occured (f7f7).
qla2300 0000:04:02.0: LOOP UP detected (2 Gbps).
qla2300 0000:04:02.0: Topology - (F_Port), Host Loop address 0xffff
qla2300 0000:04:02.0:
 QLogic Fibre Channel HBA Driver: 8.00.02b5-k
  QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
  ISP2312: PCI-X (100 MHz) @ 0000:04:02.0 hdma+, host#=3, fw=3.03.08 IPX
ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 48 (level, low) -> IRQ 193
qla2300 0000:05:01.0: Found an ISP2312, irq 193, iobase 0xf886c000
scsi4 : qla2xxx
  Vendor: IBM       Model: 1722-600          Rev: 0<6>qla2300 0000:05:01.0: Conf
iguring PCI space...
520
  Type:   Direct-Access                      ANSI SCSI revision: 03
qla2300 0000:05:01.0: Configure NVRAM parameters...
SCSI device sda: 41943040 512-byte hdwr sectors (21475 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 41943040 512-byte hdwr sectors (21475 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3
Attached scsi disk sda at scsi3, channel 0, id 0, lun 0
scsi: host 3 channel 0 id 0 lun1 has a LUN larger than allowed by the host adapt
er
scsi: host 3 channel 0 id 0 lun2 has a LUN larger than allowed by the host adapt
er
scsi: host 3 channel 0 id 0 lun3 has a LUN larger than allowed by the host adapt
er
scsi: host 3 channel 0 id 0 lun4 has a LUN larger than allowed by the host adapt
er
scsi: host 3 channel 0 id 0 lun31 has a LUN larger than allowed by the host adap
ter
  Vendor: IBM       Model: ULT3580-TD2       Rev: 4772
  Type:   Sequential-Access                  ANSI SCSI revision: 03
scsi: host 3 channel 0 id 1 lun1 has a LUN larger than allowed by the host adapt
er
qla2300 0000:05:01.0: Verifying loaded RISC code...
qla2300 0000:05:01.0: Waiting for LIP to complete...
qla2300 0000:05:01.0: LIP reset occured (f800).
qla2300 0000:05:01.0: LOOP UP detected (2 Gbps).
qla2300 0000:05:01.0: Topology - (F_Port), Host Loop address 0xffff
qla2300 0000:05:01.0:
---------------------------------------------------------------------------------

Do you have any solution?

Thanks
Stephan

_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel